That steady drip from the kitchen, bathroom or laundry tap can be surprisingly hard to ignore – especially when it is keeping the household awake or adding to the water bill. Knowing how to stop a leaking tap can save water and prevent a small annoyance becoming damage around your basin, benchtop or vanity. The key is to work out where the leak is coming from before reaching for a spanner.
Most leaking taps are caused by a worn internal seal, washer, cartridge or O-ring. These parts do the hard work every time you turn the water on and off, so they eventually wear out. A simple repair is often possible, but the right approach depends on whether you have traditional separate hot and cold taps, a mixer tap or a newer ceramic-disc fitting.
First, work out where the tap is leaking
A leak from the spout after the tap has been turned off usually points to an internal part that is no longer sealing properly. On a traditional tap, that is often the jumper valve and washer. On a mixer tap, it is more likely to be the cartridge or ceramic disc assembly.
Water appearing around the handle, however, is a different problem. It can mean an O-ring, spindle seal or cartridge seal has deteriorated. If water is pooling under the basin or inside a vanity, do not assume the tap itself is at fault. A loose flexi hose, damaged isolation valve or leaking waste pipe could be the real culprit.
Take a moment to dry the tap completely, then turn it on and off while watching closely. This simple check helps you see whether water is coming from the spout, handle, base or pipework below. Correct diagnosis matters. Replacing a washer will not fix a leaking mixer cartridge, and overtightening a tap can damage the fitting further.
How to stop a leaking tap safely
Start by turning off the water supply. Many basin and kitchen taps have small isolation valves on the hot and cold water lines underneath the sink. Turn these clockwise until they stop, then open the tap to release pressure and check that the water has stopped.
If there are no working isolation valves, switch off the main water supply to the home. In many WA homes, the stop valve is near the water meter at the front of the property. If you are unsure which valve is which, or it is stiff, corroded or already leaking, it is safer to call a licensed plumber rather than force it.
Place the plug in the basin before removing anything. Small screws and parts have a real talent for disappearing down the drain. Put a towel in the basin as well to protect the surface and catch loose components.
For a traditional washer tap, the usual process is to remove the handle cap, undo the retaining screw and lift off the handle. A spanner can then be used to carefully remove the spindle. The washer sits at the bottom of the spindle assembly and may look flattened, split or hardened. Replace it with the same size and type, then reassemble the tap without over-tightening it.
Mixer taps vary far more between brands and models. Some have a small grub screw hidden behind a cap or beneath the handle, while others need a specific tool to remove the retaining nut. Once open, the cartridge needs to be matched exactly. A cartridge that looks similar but has different locating pins or measurements may not seal correctly.
Turn the water supply back on slowly once the tap is reassembled. Check around the handle, base and under-sink connections before running the tap. If it drips from the spout again, leaks from a new point or has poor water flow, turn the water off and arrange a professional repair.
The parts most often behind a dripping tap
Traditional compression taps use a rubber washer pressed against a valve seat to stop water flow. The washer is inexpensive, but it is only one part of the story. If the brass valve seat is pitted or rough, a new washer may fail quickly. The seat may need resurfacing or replacing for a lasting result.
Quarter-turn and mixer taps generally use ceramic cartridges. Their discs are durable, but grit from the water supply, age and repeated use can affect the seal. A cartridge replacement can be straightforward when the correct part is available. It becomes less straightforward when the tap is seized, the cartridge is obsolete or the body of the tap is damaged.
O-rings and seals sit around moving parts to stop water escaping near the handle or base. These can dry out, split or compress over time. If the tap is old and several components are worn, repairing one seal may only reveal the next weak point. In that situation, replacing the whole tap can be better value than repeated small repairs.
When a DIY repair makes sense – and when it does not
A homeowner can often handle a basic washer change if the tap is accessible, the isolation valves work and the fitting comes apart without force. Take a photo before dismantling the tap, and bring the old washer or cartridge to a plumbing supplier so you can match it accurately.
DIY is less suitable when the leak involves pipework, a wall-mounted tap, a mixer with an unknown cartridge, damaged threads or seized components. It is also worth getting help if the tap is connected to hot water and you cannot isolate it confidently. A small slip with a spanner can crack a brittle fitting, strip a thread or turn a drip into a flood under the vanity.
For landlords and property managers, a prompt professional repair is usually the sensible choice. A leaking tap can lead to tenant frustration, water staining and avoidable water use, while a documented repair helps keep maintenance clear and straightforward.
Signs the leak needs a licensed plumber
Call for help sooner rather than later if you notice any of the following:
- Water is leaking beneath the sink, through cabinetry or into a wall.
- The tap will not turn off, the handle is loose or the body is cracked.
- Isolation valves do not shut the water off properly.
- The leak returns soon after a washer or cartridge replacement.
- You have low pressure, discoloured water or leaks at more than one fixture.
These signs can indicate a broader issue with the tap, supply line or internal pipework. A licensed plumber can identify the fault, source the right replacement parts and make sure the repair is properly sealed. For homes across Rockingham, Perth and Mandurah, Super Tap Man can diagnose the cause clearly and provide a detailed quote before the work begins.
Help your taps last longer
Avoid wrenching taps tighter when they drip. It feels like the logical fix, but excess force can crush a washer or damage a cartridge and make the leak worse. Turn taps off firmly but gently.
Clean aerators and tap surfaces with products suitable for the fixture finish, rather than harsh abrasives. If your water flow suddenly drops, the aerator may be blocked with debris, which is a separate issue from an internal leak. Also keep an eye on the cupboard beneath sinks. Catching a slow leak early can protect timber cabinetry and prevent mouldy smells.
A leaking tap rarely fixes itself, but it does not always need to become a major plumbing job either. Shut off the water if needed, avoid forcing stubborn parts, and get the fault checked when the repair is unclear. A quiet, dry tap is one of those small household wins that makes the whole home feel looked after.







