A hot shower that turns cold halfway through is not a small household annoyance. It can be the sign of a system that is undersized, ageing or simply wrong for the way your household uses water. This tankless water heater comparison helps Perth homeowners look past the sales labels and choose a hot water setup that can keep up.
In Australia, tankless units are usually called continuous-flow hot water systems. Rather than storing a tank of heated water, they heat water as it passes through the unit. That means hot water can continue for as long as the unit has gas or power, water pressure and enough capacity for the demand.
That does not automatically make continuous flow the right choice for every home. Your available gas supply, household size, bathroom layout, solar plans and the condition of existing pipework all matter.
Tankless water heater comparison: the key difference
The biggest difference between continuous-flow and storage hot water is when the water is heated. A storage system heats and holds a set amount of water in a tank. A continuous-flow unit waits until you open a tap, then fires up and heats the water on demand.
For households that regularly run out of hot water, that on-demand operation is appealing. There is no tank to empty during a busy morning. It also avoids continually reheating a large volume of stored water, although real running costs still depend on your fuel type, household habits and tariff.
The trade-off is that a tankless system must be correctly sized. A unit with too little flow capacity may provide a perfectly good shower on its own but struggle when someone turns on another shower, the kitchen tap or a washing machine at the same time.
Continuous-flow gas systems
Gas continuous-flow units are a common option across Perth homes, particularly where natural gas is already connected. They heat water quickly, take up less room than a large tank and are well suited to families with staggered showers, baths and frequent hot water use.
Their performance is measured in litres per minute. As a broad guide, a smaller unit may suit one bathroom or a low-demand home, while a higher-capacity model is designed to supply two or more outlets at once. But litres per minute is not a simple bigger-is-better figure. The unit needs to raise incoming cold water to your selected temperature, and performance can vary with water temperature and flow.
Gas availability is a major consideration. An older gas line may not be sized to safely supply a high-capacity continuous-flow system alongside a cooktop, heater and other gas appliances. A licensed gas fitter should assess the existing line, gas meter capacity, appliance load and installation location before recommending a model.
Homes outside natural gas areas may use LPG. LPG continuous flow can be an effective solution, but bottle size, refill arrangements and usage patterns need to be considered honestly. A large household with long showers can move through LPG faster than expected.
Electric tankless systems
Electric tankless water heaters can look straightforward because they do not require gas piping or combustion flues. In practice, high-output electric units can place a substantial load on a home’s electrical supply. Some need dedicated circuits, switchboard work or a three-phase connection.
They can make sense in a smaller home, a low-use area or a property without gas, but they are not always the cheapest or easiest full-house replacement. Before choosing one, arrange an assessment of the electrical capacity and likely operating cost. A unit that is inexpensive to buy can become a frustrating choice if it cannot deliver the flow your family needs.
Storage systems still have a place
A tankless water heater comparison should not pretend storage systems are outdated. Modern gas, electric and heat-pump storage systems can be a better fit for some properties. They may suit homes with suitable solar generation, lower simultaneous demand, limited gas capacity or a practical existing tank location.
A storage system also supplies hot water without needing to instantly heat every litre as it passes through the unit. The limitation is its stored volume and recovery time. Once the tank is depleted, you may need to wait for it to reheat.
If your current system works around a predictable routine and the tank is in good condition, replacing like for like can be the sensible, lower-disruption option. If hot water demand changes often or the household has grown, continuous flow may offer more flexibility.
Size the system for real household demand
Sizing is where many hot water decisions go wrong. The number of people in the house is useful, but it is only a starting point. Two people who take short showers at different times have very different demand from two people who shower together while the dishwasher is running.
Think about how hot water is used at your place. Consider the number of bathrooms, shower heads, whether a bath is used often, peak shower times, kitchen use and appliances connected to hot water. Rental properties also need a practical system that can handle varied tenant habits without repeated call-outs.
A high-flow shower head can consume far more water than a water-efficient one. Changing the shower head or fitting flow restrictors where appropriate may reduce demand enough to change the recommended unit size. It is a small detail with a real effect on comfort and running costs.
Temperature settings matter too. Many continuous-flow systems can be set to a controlled delivery temperature, which can improve safety and reduce the need to mix in large amounts of cold water. The right approach depends on the appliance, bathroom layout and applicable plumbing requirements.
Installation details that affect cost and reliability
The unit price is only one part of the job. A clear quote should account for the removal of the old system, new valves and pipework, gas or electrical upgrades if needed, drainage, weather protection, safe clearances and commissioning.
For gas units, the installation position matters. The appliance must have suitable ventilation and clearance from openings, boundaries and other structures, in line with manufacturer instructions and Australian requirements. Moving a unit from a hidden side passage to a compliant location can add work, but it is not a corner worth cutting.
Long pipe runs can also affect how quickly hot water reaches taps. Continuous flow prevents a tank from running out, but it cannot remove the cold water sitting in pipework between the heater and your bathroom. In a large home, a plumber may discuss pipe routing or other options to reduce waiting time and water waste.
If you are replacing a corroded storage tank, inspect the surrounding pipework too. Old valves, deteriorated connections or poor water pressure can create problems that a new heater alone will not solve.
Compare running costs without guesswork
Running cost estimates should be treated as estimates, not promises. Gas prices, electricity tariffs, household behaviour, inlet water temperature and appliance efficiency all influence the final bill.
Continuous-flow gas systems avoid standing heat loss from a storage tank, particularly when hot water use is spread throughout the day. However, a large family taking long showers can still use plenty of energy. Electric continuous flow may have different upfront and supply requirements, while heat-pump storage systems can be attractive for households able to use off-peak electricity or solar power.
Ask for a comparison based on your actual home: fuel available, likely installation work, expected usage and the life left in your existing system. The cheapest quote is not always the best value if it leaves you with insufficient flow, unsuitable pipework or a system that is difficult to service.
When to repair and when to replace
A repair may be worthwhile when the fault is isolated, replacement parts are available and the system is otherwise performing well. Ignition faults, tempering valve issues, leaking connections and worn components can often be diagnosed and repaired by a licensed professional.
Replacement becomes more sensible when failures keep returning, the unit is nearing the end of its expected service life, parts are unavailable, or your household has outgrown its capacity. Rust around a storage tank, discoloured water, inconsistent temperature, unusual noises and water pooling near the unit all deserve prompt attention.
Gas hot water faults should never be treated as a DIY project. If you smell gas, suspect a leak or notice a gas appliance behaving abnormally, turn the appliance off if it is safe to do so, avoid ignition sources and arrange urgent licensed assistance.
For Rockingham, Perth and Mandurah homes, Super Tap Man can assess your current hot water setup, explain the practical options and provide a clear quote for the work required. The best choice is the one that delivers safe, dependable hot water for your household without nasty surprises at installation time or on the next utility bill.







