A gas cooktop that takes a few clicks to light, a heater that leaves a stuffy smell in the room, or hot water that keeps cutting out can be easy to put off. Yet these are common household gas safety hazards that deserve prompt attention. Gas is an efficient, dependable part of many Perth, Rockingham and Mandurah homes, but appliances, connections and ventilation need to be in safe working order.
The good news is that homeowners do not need to be gas experts to recognise when something is not right. Knowing the warning signs, what not to do, and when to call a licensed gas fitter can protect your household and prevent a smaller repair becoming an urgent situation.
A gas smell is never a wait-and-see problem
Natural gas and LPG have a distinctive added odour so leaks can be noticed quickly. If you smell gas inside or around your home, treat it seriously, even when the smell seems faint or comes and goes.
If it is safe to do so, turn off the gas appliance involved. Avoid flames of any kind, including cigarettes, candles and matches. Do not operate electrical switches, appliances, doorbells or garage remotes, and do not start a vehicle nearby. These actions can create a spark.
Get people and pets outside to fresh air. Once you are well away from the suspected leak, contact your gas network’s emergency service or call 000 if there is immediate danger, a fire, or someone is unwell. A licensed gas fitter should then find and repair the cause before the gas is used again.
A gas smell near an outdoor LPG bottle, gas meter or bayonet point also needs attention. It may be a loose connection, damaged hose, failed regulator or leaking appliance. Do not try to locate a leak with a flame or tighten fittings if you are unsure what you are doing.
Faulty gas appliances and poor combustion
Gas appliances burn fuel to create heat. When combustion is working properly, a cooktop flame is usually clear blue and stable. A flame that is persistently yellow or orange, lifts away from the burner, produces soot, or is difficult to light can signal a problem with the burner, gas pressure or air supply.
This does not mean every flicker of colour is an emergency. Cooking spills, moisture and airflow can affect a flame briefly. The concern is a repeated change in how an appliance operates, especially when it is paired with black marks around burners, a new smell, headaches, or a room that feels unusually stuffy.
Never ignore an appliance that repeatedly goes out, makes popping or whooshing noises, or needs the controls held in an unusual position to keep running. Do not keep attempting to relight it. Switch it off and arrange a professional inspection.
Carbon monoxide risks are easy to miss
Carbon monoxide is a colourless, odourless gas that can be produced when a gas appliance is not burning correctly or its flue is blocked. It is why a gas appliance may look normal while still presenting a serious risk.
Headache, dizziness, nausea, tiredness and confusion can be signs of carbon monoxide exposure, particularly if symptoms improve after leaving the house. If anyone has these symptoms while a gas heater, hot water system or other gas appliance is operating, turn it off if safe, move everyone into fresh air and seek urgent medical advice. Do not use the appliance again until it has been checked by a licensed gas fitter.
Portable gas heaters are a particular concern in enclosed rooms. Follow the manufacturer’s instructions for ventilation and intended use, and never use an outdoor gas appliance, barbecue or patio heater indoors. These appliances are not designed to operate safely in a closed living space.
Blocked vents and damaged flues
Some gas heaters and hot water systems rely on flues to carry combustion gases safely outside. A flue that is damaged, disconnected, corroded or blocked by leaves, nests or building work can allow those gases to enter the home.
Take a quick look around external flue terminals from ground level when you are doing household maintenance. Keep the area clear of stored items, garden growth and anything that could restrict air movement. Do not put your hands into a flue, remove panels, or attempt to alter it yourself.
Renovations can also create hidden gas safety issues. New cabinetry, plasterboard, insulation or enclosed outdoor areas can change ventilation around a heater or hot water system. Before enclosing, relocating or building near gas equipment, have the plan assessed by a licensed gas fitter. What looks like a simple cosmetic change can affect clearances, flue performance and safe access for servicing.
Unattended cooktops and worn kitchen connections
The kitchen is where many everyday gas incidents begin. A pot boiling over can extinguish a cooktop flame while gas continues to flow. Grease and food debris can interfere with ignition and burner performance. Loose sleeves, tea towels and packaging left close to a flame can catch fire quickly.
Stay in the kitchen when using the cooktop, turn pot handles away from the edge, and keep the area around burners clear. Clean spills once the cooktop is cool, particularly around burner caps and ignition points. If a burner will not light properly after cleaning, do not dismantle gas components to fix it.
Check flexible gas hoses and visible connections occasionally for cracking, kinks, corrosion or signs of wear. A hose should not be stretched behind an oven, trapped by cabinetry, or rubbing against sharp edges. If you are replacing a cooktop or oven, the connection and commissioning must be done by a licensed gas fitter. This is not a DIY job, even when the appliance seems like a straightforward swap.
Bayonet points, heaters and unused outlets
A gas bayonet point makes it convenient to connect a compatible portable heater, but it needs the right hose, fitting and appliance. The connection should be secure and the hose kept away from walkways, hot surfaces and places where it can be pinched by furniture.
Before connecting a heater for winter, inspect the hose and bayonet fitting for visible damage. If the appliance has been sitting in the shed or garage for months, give it a professional service rather than assuming it is ready to go. Dust, insects and general wear can affect safe operation.
Unused gas outlets need to remain properly capped and protected. Never remove a cap, alter a bayonet point or use an adaptor to make an appliance fit. If a connection feels loose or you suspect it has been damaged, stop using it and arrange a repair.
Hot water systems need room to work safely
A gas hot water system often sits out of sight until there is no hot water. Warning signs include inconsistent temperature, pilot light problems, soot, unusual noises, visible corrosion, water leaking around the unit or a gas smell nearby.
Do not store paint, petrol, pool chemicals, cardboard or household clutter around the system. Apart from fire risk, stored items can block ventilation and make it harder to spot leaks or access the unit in an emergency. Keep the area clear and make sure any external vents and flue outlets remain unobstructed.
Regular servicing is especially worthwhile for older systems, homes near the coast, and rental properties with frequent tenant changes. Salt air, corrosion and ordinary wear can shorten the life of connections and components. A service can identify small issues before the hot water system fails at the worst possible time.
Common household gas safety hazards in rentals
Landlords have responsibilities to keep rental gas installations safe, while tenants should report faults promptly and avoid unauthorised repairs. A heater that has changed performance, a cooktop burner that will not stay lit, or a suspected leak is not a maintenance request to leave until the next routine inspection.
Property managers can reduce disruption by keeping clear records of appliance servicing, gas safety checks and repairs. For tenants, the practical rule is simple: report unusual smells, soot, unreliable ignition, damaged connections and hot water faults as soon as you notice them. Do not try to repair gas equipment yourself or ask an unlicensed person to do it.
When to call a licensed gas fitter
Call for help straight away if you smell gas, hear hissing from a connection, see soot near a gas appliance, or suspect carbon monoxide exposure. For less urgent concerns, book an inspection when an appliance is unreliable, the flame has changed, a heater has not been serviced for some time, or you are renovating and moving gas equipment.
In Western Australia, gas work must be carried out by a properly licensed gas fitter. The right professional will inspect the appliance and pipework, explain what has been found, provide clear options for repair or replacement, and test the work before the appliance goes back into service.
Gas problems rarely improve through repeated relighting or a quick DIY adjustment. If something does not look, smell or operate as it should, give it the attention it deserves. A prompt safety check from a local licensed team like Super Tap Man can bring back the simple peace of mind every home should have.







